Tender For Various Fabrication & Hand Railing Jobs At Crm1 For Cy2025 o PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details 1 2000158160 10 10 10 DISMANTLING OF STRUCTURE 50 TO 20 SERVICES FOR GENERAL FABRICATION 100 TO 30 FABRICATION & ERECTION OF STRUCTURAL 50 TO Email : Manoj.Lalvani@amns.in Contact : 9879101878 Name : Lalvani, Manoj - AM/NS India - CRM - Ope Item Details : * Scope of work For Vendor: -Service for general fabrication at various locations. -Fabrication and erection Structures at Height work. -Dismantling existing structures as per requirement. -Tools, Tackles, Grinding M/C etc. -Supply of manpower with proper PPES -Welding M/C, Cutting set, Cylinders. -Fabrication consumables like welding electrodes, grinding wheels. -Supervisor in contractor scope -Job to be done as per instructions by line in-charge only. Scope of Work- AMNS - Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) - Essentials like electricity, water etc. - Crane and hydra will be provided if required. - Scaffolding or Man lifter will be provided if required. - Vehicle will be provided for scrap loading and disposal work. - Specific Penalty for safety violation and non-performance by vendor. Specific Penalty for nonperformance by vendor and must be cardinally measured. AMNS Safety Rule and Regulation as per Company Policy: • All the Persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(CNH). • All the workers have authorized work at height valid pass. • Work should be started only after taking authorized work permit. • Toolbox talk must be delivery before starting the job on daily basic. • Use certified portable hand electric machine. • Use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • The person who is working at height should wear certified Double lanyard full body Harness (Safety Belt) <(>&<)> locked safety belt (Both clamp) with lifeline. anchoring point must be check before every use. • Use only certified two lanyards connected in a Y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • Ensure that all persons are wearing Safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / For job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • Work should be carried out in close Supervision of Competent Supervisor. • The working at height job should be allowed in daytime only • While handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. Ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with Page 2 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details bundles. • While fabrication activity ensure crane movement. Crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from working area. • While fabrication activity near DSL side, ensure DSL power supply must be cut off <(>&<)> for that LOTOTO must be taken for isolation of DSL power supply. • While fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • While scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • The working area need to be cleaned to avoid the slipping hazards. • Ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. • Ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • Always carry FE near workplace. • Never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • Ensure loose cylinder should not be kept at shop floor. • No oxygen or acetylene gas shall be used for pressure testing purpose. • No oxygen or acetylene gas shall be used for cleaning purposes. • Always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. *SOP No / Hirac No -AMNSIL/CRM/PKL-OPR/16.7/HIRAC/28 Item Note : 2 2000158160 20 20 10 DISMANTLING OF STRUCTURE 50 TO 20 SERVICES FOR GENERAL FABRICATION 100 TO 30 FABRICATION & ERECTION OF STRUCTURAL 50 TO Email : Manoj.Lalvani@amns.in Contact : 9879101878 Name : Lalvani, Manoj - AM/NS India - CRM - Ope Item Details : * Scope of work For Vendor: -Service for general fabrication at various locations. -Fabrication and erection Structures at Height work. -Dismantling existing structures as per requirement. -Tools, Tackles, Grinding M/C etc. -Supply of manpower with proper PPES -Welding M/C, Cutting set, Cylinders. -Fabrication consumables like welding electrodes, grinding wheels. -Supervisor in contractor scope -Job to be done as per instructions by line in-charge only. Scope of Work- AMNS - Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) - Essentials like electricity, water etc. - Crane and hydra will be provided if required. - Scaffolding or Man lifter will be provided if required. - Vehicle will be provided for scrap loading and disposal work. - Specific Penalty for safety violation and non-performance by vendor. Specific Penalty for nonperformance by vendor and must be cardinally measured. AMNS Safety Rule and Regulation as per Company Policy: • All the Persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(CNH). Page 3 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details • All the workers have authorized work at height valid pass. • Work should be started only after taking authorized work permit. • Toolbox talk must be delivery before starting the job on daily basic. • Use certified portable hand electric machine. • Use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • The person who is working at height should wear certified Double lanyard full body Harness (Safety Belt) <(>&<)> locked safety belt (Both clamp) with lifeline. anchoring point must be check before every use. • Use only certified two lanyards connected in a Y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • Ensure that all persons are wearing Safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / For job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • Work should be carried out in close Supervision of Competent Supervisor. • The working at height job should be allowed in daytime only • While handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. Ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • While fabrication activity ensure crane movement. Crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from working area. • While fabrication activity near DSL side, ensure DSL power supply must be cut off <(>&<)> for that LOTOTO must be taken for isolation of DSL power supply. • While fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • While scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • The working area need to be cleaned to avoid the slipping hazards. • Ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. • Ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • Always carry FE near workplace. • Never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • Ensure loose cylinder should not be kept at shop floor. • No oxygen or acetylene gas shall be used for pressure testing purpose. • No oxygen or acetylene gas shall be used for cleaning purposes. • Always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. SOP- AMNSIL/CRM/HSPM_SLT-OPR/022/SOP HIRAC -AMNSIL/CRM/HSPM_SLT-OPR/HIRAC/67 Item Note : 3 2000158160 30 30 10 DISMANTLING OF STRUCTURE 50 TO 20 SERVICES FOR GENERAL FABRICATION 100 TO 30 FABRICATION & ERECTION OF STRUCTURAL 50 TO Email : Manoj.Lalvani@amns.in Contact : 9879101878 Name : Lalvani, Manoj - AM/NS India - CRM - Ope Item Details : * Scope of work For Vendor: -Service for general fabrication at various locations. -Fabrication and erection Structures at Height work. -Dismantling existing structures as per requirement. -Tools, Tackles, Grinding M/C etc. Page 4 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details -Supply of manpower with proper PPES -Welding M/C, Cutting set, Cylinders. -Fabrication consumables like welding electrodes, grinding wheels. -Supervisor in contractor scope -Job to be done as per instructions by line in-charge only. Scope of Work- AMNS - Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) - Essentials like electricity, water etc. - Crane and hydra will be provided if required. - Scaffolding or Man lifter will be provided if required. - Vehicle will be provided for scrap loading and disposal work. - Specific Penalty for safety violation and non-performance by vendor. Specific Penalty for nonperformance by vendor and must be cardinally measured. AMNS Safety Rule and Regulation as per Company Policy: • All the Persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(CNH). • All the workers have authorized work at height valid pass. • Work should be started only after taking authorized work permit. • Toolbox talk must be delivery before starting the job on daily basic. • Use certified portable hand electric machine. • Use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • The person who is working at height should wear certified Double lanyard full body Harness (Safety Belt) <(>&<)> locked safety belt (Both clamp) with lifeline. anchoring point must be check before every use. • Use only certified two lanyards connected in a Y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • Ensure that all persons are wearing Safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / For job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • Work should be carried out in close Supervision of Competent Supervisor. • The working at height job should be allowed in daytime only • While handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. Ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • While fabrication activity ensure crane movement. Crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from working area. • While fabrication activity near DSL side, ensure DSL power supply must be cut off <(>&<)> for that LOTOTO must be taken for isolation of DSL power supply. • While fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • While scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • The working area need to be cleaned to avoid the slipping hazards. • Ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. Page 5 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details • Ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • Always carry FE near workplace. • Never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • Ensure loose cylinder should not be kept at shop floor. • No oxygen or acetylene gas shall be used for pressure testing purpose. • No oxygen or acetylene gas shall be used for cleaning purposes. • Always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. HIRAC_AMNSIL/CRM/CTCM-OPR/16.7/HIRAC/36 SOP_AMNSIL/CRM/CTCM-OPR/19/SOP/18 Item Note : 4 2000158160 40 40 10 DISMANTLING OF STRUCTURE 50 TO 20 SERVICES FOR GENERAL FABRICATION 100 TO 30 FABRICATION & ERECTION OF STRUCTURAL 50 TO Email : Manoj.Lalvani@amns.in Contact : 9879101878 Name : Lalvani, Manoj - AM/NS India - CRM - Ope Item Details : * Scope of work For Vendor: -Service for general fabrication at various locations. -Fabrication and erection Structures at Height work. -Dismantling existing structures as per requirement. -Tools, Tackles, Grinding M/C etc. -Supply of manpower with proper PPES -Welding M/C, Cutting set, Cylinders. -Fabrication consumables like welding electrodes, grinding wheels. -Supervisor in contractor scope -Job to be done as per instructions by line in-charge only. Scope of Work- AMNS - Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) - Essentials like electricity, water etc. - Crane and hydra will be provided if required. - Scaffolding or Man lifter will be provided if required. - Vehicle will be provided for scrap loading and disposal work. - Specific Penalty for safety violation and non-performance by vendor. Specific Penalty for nonperformance by vendor and must be cardinally measured. AMNS Safety Rule and Regulation as per Company Policy: • All the Persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(CNH). • All the workers have authorized work at height valid pass. • Work should be started only after taking authorized work permit. • Toolbox talk must be delivery before starting the job on daily basic. • Use certified portable hand electric machine. • Use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • The person who is working at height should wear certified Double lanyard full body Harness (Safety Belt) <(>&<)> locked safety belt (Both clamp) with lifeline. anchoring point must be check before every use. • Use only certified two lanyards connected in a Y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • Ensure that all persons are wearing Safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / For job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • Work should be carried out in close Supervision of Competent Supervisor. • The working at height job should be allowed in daytime only Page 6 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details • While handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. Ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • While fabrication activity ensure crane movement. Crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from working area. • While fabrication activity near DSL side, ensure DSL power supply must be cut off <(>&<)> for that LOTOTO must be taken for isolation of DSL power supply. • While fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • While scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • The working area need to be cleaned to avoid the slipping hazards. • Ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. • Ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • Always carry FE near workplace. • Never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • Ensure loose cylinder should not be kept at shop floor. • No oxygen or acetylene gas shall be used for pressure testing purpose. • No oxygen or acetylene gas shall be used for cleaning purposes. • Always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. HIRAC_ SOP_ Item Note : 5 2000158160 50 50 10 DISMANTLING OF STRUCTURE 50 TO 20 SERVICES FOR GENERAL FABRICATION 100 TO 30 FABRICATION & ERECTION OF STRUCTURAL 50 TO Email : Manoj.Lalvani@amns.in Contact : 9879101878 Name : Lalvani, Manoj - AM/NS India - CRM - Ope Item Details : * Scope of work For Vendor: -Service for general fabrication at various locations. -Fabrication and erection Structures at Height work. -Dismantling existing structures as per requirement. -Tools, Tackles, Grinding M/C etc. -Supply of manpower with proper PPES -Welding M/C, Cutting set, Cylinders. -Fabrication consumables like welding electrodes, grinding wheels. -Supervisor in contractor scope -Job to be done as per instructions by line in-charge only. Scope of Work- AMNS - Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) - Essentials like electricity, water etc. - Crane and hydra will be provided if required. - Scaffolding or Man lifter will be provided if required. - Vehicle will be provided for scrap loading and disposal work. - Specific Penalty for safety violation and non-performance by vendor. Specific Penalty for nonperformance by vendor and must be cardinally measured. AMNS Safety Rule and Regulation as per Company Policy: • All the Persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the Page 7 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details hospital(CNH). • All the workers have authorized work at height valid pass. • Work should be started only after taking authorized work permit. • Toolbox talk must be delivery before starting the job on daily basic. • Use certified portable hand electric machine. • Use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • The person who is working at height should wear certified Double lanyard full body Harness (Safety Belt) <(>&<)> locked safety belt (Both clamp) with lifeline. anchoring point must be check before every use. • Use only certified two lanyards connected in a Y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • Ensure that all persons are wearing Safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / For job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • Work should be carried out in close Supervision of Competent Supervisor. • The working at height job should be allowed in daytime only • While handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. Ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • While fabrication activity ensure crane movement. Crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from working area. • While fabrication activity near DSL side, ensure DSL power supply must be cut off <(>&<)> for that LOTOTO must be taken for isolation of DSL power supply. • While fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • While scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • The working area need to be cleaned to avoid the slipping hazards. • Ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. • Ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • Always carry FE near workplace. • Never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • Ensure loose cylinder should not be kept at shop floor. • No oxygen or acetylene gas shall be used for pressure testing purpose. • No oxygen or acetylene gas shall be used for cleaning purposes. • Always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. HIRAC_ SOP_ Item Note : 6 2000158160 60 60 10 DISMANTLING OF STRUCTURE 50 TO 20 SERVICES FOR GENERAL FABRICATION 100 TO 30 FABRICATION & ERECTION OF STRUCTURAL 50 TO Email : Manoj.Lalvani@amns.in Contact : 9879101878 Name : Lalvani, Manoj - AM/NS India - CRM - Ope Item Details : * Scope of work For Vendor: -Service for general fabrication at various locations. -Fabrication and erection Structures at Height work. -Dismantling existing structures as per requirement. -Tools, Tackles, Grinding M/C etc. Page 8 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details -Supply of manpower with proper PPES -Welding M/C, Cutting set, Cylinders. -Fabrication consumables like welding electrodes, grinding wheels. -Supervisor in contractor scope -Job to be done as per instructions by line in-charge only. Scope of Work- AMNS - Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) - Essentials like electricity, water etc. - Crane and hydra will be provided if required. - Scaffolding or Man lifter will be provided if required. - Vehicle will be provided for scrap loading and disposal work. - Specific Penalty for safety violation and non-performance by vendor. Specific Penalty for nonperformance by vendor and must be cardinally measured. AMNS Safety Rule and Regulation as per Company Policy: • All the Persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(CNH). • All the workers have authorized work at height valid pass. • Work should be started only after taking authorized work permit. • Toolbox talk must be delivery before starting the job on daily basic. • Use certified portable hand electric machine. • Use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • The person who is working at height should wear certified Double lanyard full body Harness (Safety Belt) <(>&<)> locked safety belt (Both clamp) with lifeline. anchoring point must be check before every use. • Use only certified two lanyards connected in a Y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • Ensure that all persons are wearing Safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / For job bellow 4 metre height full body double lanyard safety harness without shock absorber to be used. • Work should be carried out in close Supervision of Competent Supervisor. • The working at height job should be allowed in daytime only • While handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. Ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • While fabrication activity ensure crane movement. Crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from working area. • While fabrication activity near DSL side, ensure DSL power supply must be cut off <(>&<)> for that LOTOTO must be taken for isolation of DSL power supply. • While fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • While scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • The working area need to be cleaned to avoid the slipping hazards. • Ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. Page 9 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details • Ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • Always carry FE near workplace. • Never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • Ensure loose cylinder should not be kept at shop floor. • No oxygen or acetylene gas shall be used for pressure testing purpose. • No oxygen or acetylene gas shall be used for cleaning purposes. • Always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. HIRAC_AMNSIL/CRM/PKL-OPR/16.7/HIRAC/28 Item Note : 7 2000158163 10 70 10 DISMANTLING OF HANDRAILING 5,000 M 20 FABRICATION & ERECTION OF HAND RAILING 5,000 M Email : Manoj.Lalvani@amns.in Contact : 9879101878 Name : Lalvani, Manoj - AM/NS India - CRM - Ope Item Details : * Scope of work For Vendor: -Fabrication and erection handrailing at various location(Various Size). -Dismantling existing Handrailing as per requirement(Various Size). -Tools, Tackles, Grinding M/C etc. -Supply of manpower with proper PPES -Welding M/C, Cutting set, Cylinders. -Fabrication consumables like welding electrodes, grinding wheels. -Supervisor in contractor scope -Job to be done as per instructions by line in-charge only. -Vendor shall provide all required PPEs as per PPEs Matrix according to nature of the jobs. Safety shoes, FRP Helmet, Plane Goggle, Nitrile Dipped cut resistance hand gloves, Cotton / Canvas Gloves, Leg Guard, Arm Guard. -Good Quality of PPEs shall be provided by vendor as per AMNS standard. Scope of Work- AMNS - Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) - Essentials like electricity, water etc. - Crane and hydra will be provided if required. - Scaffolding or Man lifter will be provided if required. - Vehicle will be provided for scrap loading and disposal work. - Specific Penalty for safety violation and non-performance by vendor. Specific Penalty for nonperformance by vendor and must be cardinally measured. AMNS Safety Rule and Regulation as per Company Policy: • All the Persons working at height for exhaust pipe dismantling job should be healthy and medically fit and must be certified by the hospital(CNH). • All the workers have authorized work at height valid pass. • Work should be started only after taking authorized work permit. • Toolbox talk must be delivery before starting the job on daily basic. • Use certified portable hand electric machine. • Use certified lifting tools <(>&<)> tackles <(>&<)> it should be check before every use. • The person who is working at height should wear certified Double lanyard full body Harness (Safety Belt) <(>&<)> locked safety belt (Both clamp) with lifeline. anchoring point must be check before every use. • Use only certified two lanyards connected in a Y configuration, which allows one lanyard to be attached to an anchor point while the second lanyard is being moved to a new anchor point, thus providing protection from falls at all times. • Ensure that all persons are wearing Safety helmet, safety shoe, safety goggles, face shield and cut resistance hand gloves, full body shock absorber double lanyard safety harness (for jobs above 4 metre height) / For job bellow 4 metre height full body double lanyard safety harness Page 10 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details without shock absorber to be used. • Work should be carried out in close Supervision of Competent Supervisor. • The working at height job should be allowed in daytime only • While handling or shifting job of dismantle exhaust pipes with crane ensure that certified lifting belt are used <(>&<)> check the belt condition before every use. Ensure exhaust pipes are lift in horizontal balance load condition <(>&<)> ensure guide rope are properly tied with bundles. • While fabrication activity ensure crane movement. Crane movement must be restricted at working area when ever needed <(>&<)> for that working area must be barricade with danger tape <(>&<)> also manual stopper to be provided on both side of crane rail track minimum 8 meter away from working area. • While fabrication activity near DSL side, ensure DSL power supply must be cut off <(>&<)> for that LOTOTO must be taken for isolation of DSL power supply. • While fabrication activity ensure that ground area should be barricade with danger tape to avoid unauthorized entry in work area • While scaffolding needed for work ensure that it must be certified <(>&<)> also ensure crane movement <(>&<)> if required crane movement must be restricted at scaffolding area. • The working area need to be cleaned to avoid the slipping hazards. • Ensure gas cutting spark should not be fall on any electrical wires, trench cover <(>&<)> on any flammable material for that all wires /trench cover must be cover with fire blanket <(>&<)> all flammable materials should be removed from work area before starting the job. • Ensure highly flammable material should not be store near working area <(>&<)> if any it should be removed immediately before starting the job. • Always carry FE near workplace. • Never transport cylinders with regulators and hose attached unless a proper trolley or carrier is used with locking chains. • Ensure loose cylinder should not be kept at shop floor. • No oxygen or acetylene gas shall be used for pressure testing purpose. • No oxygen or acetylene gas shall be used for cleaning purposes. • Always use red hose for acetylene and blue / black for oxygen, be careful to see they are never interchange. SOP- AMNSIL/CRM/HSPM_SLT-OPR/022/SOP HIRAC -AMNSIL/CRM/HSPM_SLT-OPR/HIRAC/67 * AM/NS scope: 1. Required material provide for fabrication (PIPE, ANGLE, CHENNEL AND SHEET) 2. Essentials like electricity, water etc. * AMNS Safety Rule and Regulation as per Company Policy: - All necessary safety PPE’s i.e. safety shoes, leather gloves, goggles, masks, face shield etc. in contractor scope - All work to be carried out as per safety norms which shall be guided to AM/NS team during work <(>&<)> no tolerance in safety will be accepted and penalty to be imposed if any violation. - Contractor shall not proceed with next activity until previous activity will be checked and approved by Representative. - All required tools <(>&<)> tackles will provide by contractor - Contractor shall deploy and provide one full time engineer to supervise the project and has experienced of carrying out such type of work. - Contractor will provide all required consumable items for the job - Contractor shall be responsible for procuring, supplying, transporting, and providing all labour, materials, tools and equipment Page 11 of 11 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000120994 Date 26.09.2024 Submission Date 13.10.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Venkat Sai Taneeru Contact Email venkat.taneeru@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details etc., required for completion of the work. - All materials shall be stored in a proper manner protected from natural elements so as to avoid contamination and deterioration. - Workers working on the site shall be skilled in their job and have related job experience. - The contractor shall guarantee that all work performed will be free from all defects in workmanship and materials and that all installation will provide the capacities and characteristics specified. * HIRAC AMNSIL/CRM/CTCM-OPR/16.7/HIRAC/36 AMNSIL/CRM/PKL-OPR/16.7/HIRAC/28 AMNSIL/CRM/PWH/16.7/HIRAC/33 AMNSIL/CRM/PWH/16.7/HIRAC/39 * SOP AMNSI/CRM/6-HI-REV/OPR/19/SOP/18 AMNSIL/CRM/CTCM-OPR/19/SOP/18 AMNSIL/CRM/PWH/19/SOP/34